126 Models Clutch/Brake Units – Motor-coupled Type

Specifications

Downloads

126-□-4B Types

[Specifications]

Model	Size	Motor output[kW] 4P	Dynamic friction torque Td [N･m]	Static friction torque Ts [N･m]	Coil(at20℃)				Heat resistance class	Rotating part moment of inertia [kg･m²]	Total work performed until readjustment of the air gap ET [J]	Armature pull-in time ta[s]	Torque build-up time tp[s]	Torque decaying time td[s]	Mass [kg]
Model	Size	Motor output[kW] 4P	Dynamic friction torque Td [N･m]	Static friction torque Ts [N･m]	Voltage [V]	Wattage [W]	Current [A]	Resistance [Ω]	Heat resistance class	Rotating part moment of inertia [kg･m²]		Armature pull-in time ta[s]	Torque build-up time tp[s]	Torque decaying time td[s]	Mass [kg]
126-06-4B-0.2kW	06	0.2	5	5.5	DC24	11	0.46	52	B	1.28×10^-4	36×10⁶	C:0.020 B:0.015	C:0.041 B:0.033	C:0.020 B:0.015	8.9
126-08-4B-0.4kW	08	0.4	10	11	DC24	15	0.63	38	B	3.70×10^-4	60×10⁶	C:0.023 B:0.016	C:0.051 B:0.042	C:0.030 B:0.025	13
126-10-4B-0.75kW-IE3	10	0.75	20	22	DC24	20	0.83	29	B	1.40×10^-3	130×10⁶	C:0.025 B:0.018	C:0.063 B:0.056	C:0.050 B:0.030	20
126-12-4B-1.5kW-IE3	12	1.5	40	45	DC24	25	1.04	23	B	3.85×10^-3	250×10⁶	C:0.040 B:0.027	C:0.115 B:0.090	C:0.065 B:0.050	41
126-16-4B-2.2kW-IE3	16	2.2	80	90	DC24	35	1.46	16	B	1.35×10^-2	470×10⁶	C:0.050 B:0.035	C:0.160 B:0.127	C:0.085 B:0.055	54
126-16-4B-3.7kW-IE3	16	3.7	80	90	DC24	35	1.46	16	B	1.35×10^-2	470×10⁶	C:0.050 B:0.035	C:0.160 B:0.127	C:0.085 B:0.055	69

*The induction motors are fully sealed external fan motors that conform to the JIS C4210 standard (for 0.2 kW and 0.4 kW models) or the JIS C 4213 standard (for 0.75 kW models or higher).

*The power supplies for the motors are 3-phase, 200 V AC at 50 Hz, or 200/220 V AC at 60 Hz.

*If you desire a special voltage (5 Power Supply Specifications), different number of poles, or the like for the induction motor, contact Miki Pulley.

*The dynamic friction torque, Td, is measured at a relative speed of 100 min-1. Depending on the initial torque characteristics, break-in to condition the engaging surfaces may also be required.

[Dimensions]

Model	Dimensions of part																			Dimensions of shaft
Model	A1	A2	B1	B2	C	D1	D2	E	F1	F2	G	J	K	L	H	T	Y	Z1	Z2	Q	S	U	V	W
126-06-4B-0.2kW	65	90	90	105	65	100	130	27.5	61	－	2.6	48.5	102	335	－	－	3	13.5	6.5	25	11	12.5	M4×0.7length8	4
126-08-4B-0.4kW	80	110	110	130	80	125	145	32.5	72	126.5	3.2	63	127.5	389	167.5	－	2.5	15.5	9	30	14	16	M4×0.7length8	5
126-10-4B-0.75kW-IE3	105	135	140	160	90	150	163	35	81	136	3.2	80	154	462	184	－	3	20	11.5	40	19	21	M6×1length11	5
126-12-4B-1.5kW-IE3	135	160	175	185	112	190	182/176	42.5	97	148.5	15	108	194	550.5	－	244.5	3	24.5	11.5	50	24	27	M6×1length11	7
126-16-4B-2.2kW-IE3	155	200	200	230	132	230	198/195	45	109	155.5	18	135	256	649.5	－	286	4	28	14	50	24	27	M6×1length11	7
126-16-4B-3.7kW-IE3	155	200	200	230	132	230	225/215	45	109	168.5	18	145	256	681	－	295	4	28	14	60	28	31	M6×1length11	7

*The output shaft keyways are old JIS standard class 2 while the key is old JIS standard class 1.

*When inserting pulleys or the like onto output shafts, use the supplied insertion set.

*These models are cast basded on a motor output of 1.5 kW or greater.

126-□-4F-N Types